Skip to main content
Arduino

Return to Question

Made it a better to understand.
Source Link
Nick Gammon ♦
Nick Gammon ♦
  • 38.9k
  • 13
  • 70
  • 126

Arduino Mega2560 clone responding slowslowly

I am using an Arduino Mega2560. Using Arduino Mega as ISP to burn sketch, I had loaded the bootloader from Arduino IDE.

I uploaded the blink ledLED code to the Mega. But the ledLED is responding slowslowly. Same with Serial code. Delay of 0.1 second acting as 1 second on my board. In code serial communication baudratebaud-rate is 9600 but I am getting proper value when I set the baudratebaud-rate to 4800 in serial monitor.

Could anyone point out the problem? Thanks

Arduino Mega2560 clone responding slow

I am using an Arduino Mega2560. Using Arduino Mega as ISP to burn sketch, I had loaded bootloader from Arduino IDE.

I uploaded the blink led code to the Mega. But the led is responding slow. Same with Serial code. Delay of 0.1 second acting as 1 second on my board. In code serial communication baudrate is 9600 but I am getting proper value when I set the baudrate to 4800 in serial monitor.

Could anyone point out the problem? Thanks

Arduino Mega2560 clone responding slowly

I am using an Arduino Mega2560. Using Arduino Mega as ISP to burn sketch, I had loaded the bootloader from Arduino IDE.

I uploaded the blink LED code to the Mega. But the LED is responding slowly. Same with Serial code. Delay of 0.1 second acting as 1 second on my board. In code serial communication baud-rate is 9600 but I am getting proper value when I set the baud-rate to 4800 in serial monitor.

Could anyone point out the problem?

Made it a better to understand.
Source Link
edit approved Aug 28, 2015 at 21:53
Avamander
edit approved Aug 28, 2015 at 21:53
Avamander
  • 624
  • 2
  • 12
  • 36

MEga256 Arduino Mega2560 clone responding slow

I had used the Mega256 SCh to build my board,am using an Arduino Mega2560. Using Arduino megaMega as ISP to burn sketch, I had loaded boot loaderbootloader from Arduino IDE. and when 

I downloadeduploaded the blink led code to the Mega. LedBut the led is responding slow. sameSame with Serial code. delay Delay of 1000.1 second acting as of 10001 second on my board in. In code baud rate inserial communication baudrate is 9600 but iI am getting proper value when iI set the baudrate to 4800 in serial monitor. Can any one

Could anyone point out the problem? Thanks

MEga256 clone responding slow

I had used the Mega256 SCh to build my board, Using Arduino mega as ISP to burn sketch, I had loaded boot loader from Arduino IDE. and when I downloaded the blink led code. Led responding slow. same with Serial code. delay of 100 acting as of 1000 on my board in code baud rate in 9600 but i am getting proper value when i set 4800 in serial monitor. Can any one point out the problem Thanks

Arduino Mega2560 clone responding slow

I am using an Arduino Mega2560. Using Arduino Mega as ISP to burn sketch, I had loaded bootloader from Arduino IDE. 

I uploaded the blink led code to the Mega. But the led is responding slow. Same with Serial code. Delay of 0.1 second acting as 1 second on my board. In code serial communication baudrate is 9600 but I am getting proper value when I set the baudrate to 4800 in serial monitor.

Could anyone point out the problem? Thanks

Source Link
Gajendra Kushwah
Gajendra Kushwah
  • 1

MEga256 clone responding slow

I had used the Mega256 SCh to build my board, Using Arduino mega as ISP to burn sketch, I had loaded boot loader from Arduino IDE. and when I downloaded the blink led code. Led responding slow. same with Serial code. delay of 100 acting as of 1000 on my board in code baud rate in 9600 but i am getting proper value when i set 4800 in serial monitor. Can any one point out the problem Thanks