I have followed all the steps given by per1234 and received below error from avrdude. Any help will be much appreciated.
Note - To follow per1234 steps i have upgraded Arduino from 1.6.9 (32 bit) to Arduino 1.8.4
C:\Program Files (x86)>F:\SIMBU\IoT\arduino-1.8.4\hardware\tools\avr\bin\avrdude -CF:\SIMBU\IoT\arduino-1.8.4\hardware\tools\avr\etc/avrdude.conf -v -c arduino -p atmega16 -P net:192.168.1.102:328 -Uflash:w:C:\Users\KAVIG~1.LAP\AppData\Local\Temp\arduino_build_138155/Blink.ino.hex:i
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "F:\SIMBU\IoT\arduino-1.8.4\hardware\tools\avr\etc/avrdude.conf"
Using Port : net:192.168.1.102:328
Using Programmer : arduino
avrdude: ser_drain(): read error: The parameter is incorrect.
avrdude: ser_drain(): read error: The parameter is incorrect.
avrdude: ser_drain(): read error: The parameter is incorrect.
AVR Part : ATmega16
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 4 10 128 0 no 512 4 0 9000 9000 0xff 0xff
flash 33 6 128 0 yes 16384 128 128 4500 4500 0xff 0xff
lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
calibration 0 0 0 0 no 4 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x14
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x10
Hardware Version: 4728160
Firmware Version: 0.2
Topcard : STK502
Vtarget : 1.8 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: stk500_initialize(): (b) protocol error, expect=0x10, resp=0x01
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x10
avrdude done. Thank you.
