My arduino cannot connect to any port of my computer. So far i tried the following, without any luck:

1. Using another arduino to check the usb, and it worked. So no problem with usb cable.
2. Resetting the arduino (double tap the reset-button)
3. Inserting deleting and updating the drivers from the device manager
4. Deleting the drivers, and then inserting the arduino while pressing the reset button.
5. Connecting the arduino to a different pc and it still doesn't work.

Is there something else i can do? Or is it permenantly damaged?

When i connect to to the computer, this comes up:

In my device manager, i see the following:

Also, in the IDE, i cannot select any port.

Extra info : I was trying to use Serial2 from another arduino to this, so i was changing some jumper wires while they were powered. So it is possible it is damaged.

EDIT: i tried uploading to another arduino, and i got this message:

My arduino cannot connect to any port of my computer. So far i tried the following, without any luck:

1. Using another arduino to check the usb, and it worked. So no problem with usb cable.
2. Resetting the arduino (double tap the reset-button)
3. Inserting deleting and updating the drivers from the device manager
4. Deleting the drivers, and then inserting the arduino while pressing the reset button.
5. Connecting the arduino to a different pc and it still doesn't work.
6. I followed everything listed here. (Resetting, uploading a uf2 blink file). I even compiled my blink uf2 file, with the newest version of mbed os for rp2040. And i even tried with older versions of the mbed os.
7. I tried uploading a flash_nuke.uf2 file

Is there something else i can do? Or is it permenantly damaged?

When i connect to to the computer, this comes up:

In my device manager, i see the following:

Also, in the IDE, i cannot select any port.

Extra info : I was trying to use Serial2 from another arduino to this, so i was changing some jumper wires while they were powered. So it is possible it is damaged. I also tried uploading some sketches to use a second serial with some modifications to the core of the OS. The changes were on the spirit of this post, but not necessairily the same.

My arduino cannot connect to any port of my computer. So far i tried the following, without any luck:

1. Using another arduino to check the usb, and it worked. So no problem with usb cable.
2. Resetting the arduino (double tap the reset-button)
3. Inserting deleting and updating the drivers from the device manager
4. Deleting the drivers, and then inserting the arduino while pressing the reset button.
5. Connecting the arduino to a different pc and it still doesn't work.

Is there something else i can do? Or is it permenantly damaged?

When i connect to to the computer, this comes up:

In my device manager, i see the following:

Also, in the IDE, i cannot select any port.

Extra info : I was trying to use Serial2 from another arduino to this, so i was changing some jumper wires while they were powered. So it is possible it is damaged.

My arduino cannot connect to any port of my computer. So far i tried the following, without any luck:

1. Using another arduino to check the usb, and it worked. So no problem with usb cable.
2. Resetting the arduino (double tap the reset-button)
3. Inserting deleting and updating the drivers from the device manager
4. Deleting the drivers, and then inserting the arduino while pressing the reset button.
5. Connecting the arduino to a different pc and it still doesn't work.

Is there something else i can do? Or is it permenantly damaged?

When i connect to to the computer, this comes up:

In my device manager, i see the following:

Also, in the IDE, i cannot select any port.

Extra info : I was trying to use Serial2 from another arduino to this, so i was changing some jumper wires while they were powered. So it is possible it is damaged.

EDIT: i tried uploading to another arduino, and i got this message: