diff options
Diffstat (limited to 'arch/arm')
4 files changed, 19 insertions, 5 deletions
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts index aa9576d8ab5693..48ca25f57ef612 100644 --- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts @@ -1254,3 +1254,17 @@ max-frequency = <25000000>; bus-width = <4>; }; + +/* + * FIXME: rgmii delay is introduced by MAC (configured in u-boot now) + * instead of PCB on fuji board, so the "phy-mode" should be updated to + * "rgmii-[tx|rx]id" when the aspeed-mac driver can handle the delay + * properly. + */ +&mac3 { + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <ðphy3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii4_default>; +}; diff --git a/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts index ac44c745bdf8e6..a39a021a39107e 100644 --- a/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts +++ b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts @@ -55,8 +55,8 @@ mdio { /delete-node/ switch@1e; - bcm54210e: ethernet-phy@0 { - reg = <0>; + bcm54210e: ethernet-phy@25 { + reg = <25>; }; }; }; diff --git a/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts index 06545a6052f716..43ff5eafb2bb81 100644 --- a/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts +++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts @@ -259,7 +259,7 @@ pinctrl-0 = <&pinctrl_audmux>; status = "okay"; - ssi2 { + mux-ssi2 { fsl,audmux-port = <1>; fsl,port-config = < (IMX_AUDMUX_V2_PTCR_SYN | @@ -271,7 +271,7 @@ >; }; - aud3 { + mux-aud3 { fsl,audmux-port = <2>; fsl,port-config = < IMX_AUDMUX_V2_PTCR_SYN diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts index 107b00b9a93997..540642e99a4159 100644 --- a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts +++ b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts @@ -136,7 +136,7 @@ interrupt-parent = <&gpio2>; interrupts = <8 IRQ_TYPE_EDGE_FALLING>; reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; - report-rate-hz = <6>; + report-rate-hz = <60>; /* settings valid only for Hycon touchscreen */ touchscreen-size-x = <1280>; touchscreen-size-y = <800>; |